logo canson
logo canson

Tutorial y consejos artísticos

Etching (hard varnish)

Twitter icon

Puntúe este artículo

Estimated time: 3 hours  

Level: Beginner

Artist: Charlotte Reine



Etching makes it possible to create a line engraving based on an original drawing that is faithful to the model. Whether it is a personal creation or inspired by an existing image, be daring and make your first foray into the world of engraving, you will be surprised by the results!


A 6 to 10 cm copper plate, liquid engraving varnish, a drypoint, one sheet of Canson® tissue paper, blanc de Meudon, white spirit, methylated spirit, intaglio ink, a flat brush, 1 metre of tarlatan, a cotton cloth, packaging tape, a pair of scissors and a ballpoint pen.


Papier Canson® Edition 250 or 320 gsm


A small copperplate press. A plastic tray for the ferric acid


Photographie : La profondeur de champ (PDC)

1. Cleaning the plate


Clean your copper plate with a pinch of blanc de Meudon mixed with a drop of methylated spirit.

Wipe the mixture with a clean cloth.




Photographie : La profondeur de champ (PDC)

2. Applying the varnish


Using the flat brush, apply the engraving varnish onto the clean plate in a thin, even layer.

Allow to dry for at least an hour. Drying time will depend on room temperature.




Photographie : La profondeur de champ (PDC)

3. Preparing for drawing


Place a fine tissue paper on the drawing to be reproduced.

Trace your drawing using a dark ballpoint pen so that the line is visible on both sides of the paper.




Photographie : La profondeur de champ (PDC)

4. Transferring the drawing


Softly rub your tissue paper with blanc de Meudon, spread over the entire surface of the drawing. Remove any excess powder.

Place the paper on the copper plate, with the powdered side on the varnish.

Fold the edge of the paper under one side of the plate to keep it in place during the transfer. Remember to turn your drawing over if you want it to have the same direction as the original.

Delicately redraw you image. You will engrave the finer details directly onto the plate. Remove the paper. The image has been transferred to the plate.

Photographie : La profondeur de champ (PDC)

5. Engraving the plate


Using your drypoint, go over your lines again with the varnish, pressing firmly enough to expose the metal.

Do not hesitate to shade the thickness of your lines for a richer finish.

Clean your plate as you work with a little methylated spirit.

Remember to check that there is no varnish missing. You still have time to rectify by reapplying a little varnish, but remember to let it dry.


Photographie : La profondeur de champ (PDC)

6. The ferric chloride bath


Protect the back of your plate with packaging tape.

Let approximately 10 cm of tape protrude over one side of the tray to form a tab with which you can hold your plate in the tray.

Submerge your copper in the ferric chloride bath, with the image facing upwards and the tab protruding over the side, for approximately 20 minutes. The longer you leave the plate in the bath, the deeper the metal will be bitten.

With practice, you will be able to adjust the time you leave your plate in the bath according to the desired results. Carefully clean with white spirit and remove the tape from the back.

Photographie : La profondeur de champ (PDC)

7. Inking the plate


Proceed to ink the plate, rubbing firmly with a tarlatan dabber so that the ink penetrates into the grooves.

Wipe excess ink away with the tarlatan. Finish wiping with a silk scarf.

Wipe the edges by rubbing a clean cloth along the four sides of the plate. (See tricks of the trade: How to ink, wipe and produce good prints?)



Photographie : La profondeur de champ (PDC)

8. Printing


Place your inked plate on the press, in the frame you prepared previously.

Position your damp paper, pass through the press and discover your etching!

Productos sugeridos

Canson® Edition

También puede interesarle

Realizar distintos matices de un color con la técnica de la aguatinta.
La aguatinta es una técnica que permite realizar grandes superficies lisas de color en la lámina de cobre gracias a un granulado a base de resina en polvo.
La técnica de China aplicada al grabado.
Esta sencilla técnica permite obtener en el tema grabado un fondo ligeramente distinto del de tu papel habitual, colocando un papel de China sobre la lámina durante la estampación.